Silicone seals end up in places where other elastomers fail: steam lines, outdoor enclosures, food-contact equipment, and cold-storage doors. Buyers usually arrive with the same question, which is whether silicone will survive their specific medium before they commit to a tooling order. The answer is rarely a simple yes or no, because silicone resistance depends on three separate conditions—water, temperature, and chemical exposure—and each one has its own boundary.
Silicone resists water, steam, oxygen, ozone, and UV almost indefinitely, holds its sealing force from roughly -60°C to +200°C continuously, and handles dilute acids, dilute bases, alcohols, and polar solvents well. It does not resist aromatic hydrocarbons, chlorinated solvents, fuels, ketones, or concentrated acids and bases, which swell or hydrolyse the Si-O backbone. Temperature and chemical resistance are independent properties, so a grade rated to 250 °C can still fail within an hour in acetone.
The sections below work through each of those boundaries in order, then translate them into grade, hardness, and cure-system choices you can put on a specification sheet. For buyers sourcing custom profiles rather than standard stock, Hersteller von maßgefertigten Silikondichtungen capability is worth checking early, since tooling, hardness, and cure system interact and are cheaper to settle together than in sequence.
How silicone resists water, steam, and moisture
Water resistance is the easiest property to rely on and the one buyers ask about least, probably because it’s assumed. Standard silicone absorbs very little moisture, and immersion tests in potable water and salt water leave tensile strength and elongation essentially unchanged over long service periods. The reason sits in the polymer itself: a polysiloxane backbone with methyl side groups is highly hydrophobic, so water and other polar liquids bead on the surface rather than penetrating the crosslinked network.
That hydrophobicity also drives the parts of silicone resistance that matter outdoors. Ozone, ultraviolet radiation, and general weathering have almost no effect on a properly compounded silicone part, and no antiozonant additives are needed to achieve it. This is why outdoor seals, electrical insulator housings, and weather-exposed gaskets default to silicone rather than nitrile.
Steam is water’s exception. Autoclave cycles and saturated steam up to about 150 °C are routine for silicone, and the material is regularly used in steam-contact seals and sanitary fittings. Push further and the picture changes. Long exposure to high-pressure steam above roughly 120 °C and 1.7 bar promotes hydrolysis of the Si-O bond, the same degradation route that strong acids and bases trigger, and the part will eventually harden and lose elasticity. For continuous high-pressure steam service, EPDM is generally the better choice, and it costs less.
A practical way to think about it: water at any normal temperature is safe ground for silicone, steam is safe within autoclaving conditions, and steam is a decision point once pressure climbs.
What temperature can silicone resist?
Standard silicone rubber (VMQ) works continuously from about -50 °C to +200 °C and tolerates short excursions to +300 °C. Heat-stabilized grades hold +250°C continuously and +350°C for brief peaks. On the cold side, phenyl silicone (PVMQ) stays elastic down to about -100 °C, while ordinary silicone stiffens below -50 °C but doesn’t crack the way organic rubbers do.
The thermal stability comes from bond energy. A silicon-oxygen bond carries roughly 450 kJ/mol against about 350 kJ/mol for the carbon-carbon bond in organic polymers, so the backbone resists thermal breakdown that would destroy nitrile or natural rubber. That’s also why silicone stays flexible at temperatures where other elastomers have already gone brittle or turned to gum.
Grade selection follows the application temperature band directly:
| Grade | Continuous range | Short-term peak | Min. temperature | Typical use |
|---|---|---|---|---|
| VMQ (standard) | -50 to +200°C | +300°C / 15 min | -50°C | Hoses, profiles, general seals |
| HTV (heat-stabilized) | -60 to +250°C | +350°C / 30 min | -60°C | Engine seals, oven, and industrial doors |
| PVMQ (phenyl silicone) | -100 to +200°C | +250°C | -100°C | Cryogenic, aerospace, cold-chain |
| FVMQ (fluorosilicone) | -55 to +200°C | +250°C | -55°C | Fuel and oil contact |
| LSR (liquid silicone) | -50 to +200°C | +250°C | -50°C | Medical, food contact, micro parts |
Values are typical for correctly dimensioned parts operating without simultaneous chemical attack; always confirm against the supplier’s datasheet for the specific compound.
Continuous load vs. short-term peaks
Two numbers appear on every silicone datasheet, and confusing them is the most common specification error.
Continuous service temperature is the range the material holds over thousands of hours without losing its key properties. Above that limit, oxidative embrittlement starts and progresses steadily. Short-term peak temperature is a ceiling for minutes-to-hours events—a startup spike, a sterilization cycle, a hot-wash step—beyond which damage becomes permanent.
A seal for an oven door running at 220°C steady needs HTV, not standard VMQ, even though VMQ’s short-term rating of 300°C makes it look adequate. Short-term numbers are for transients, not for design loads.
Low temperature works the same way. Standard VMQ’s glass transition sits near -120 °C, but practical service stops around -50 °C because the material becomes too stiff to seal reliably long before it reaches that point. PVMQ shifts the transition point lower with phenyl groups and stays functional to about -100°C.
What are the chemical compatibility limits of silicone?
Silicone resists water, steam, dilute acids and bases, alcohols, vegetable oils, animal fats, and polar oxygenated solvents such as acetone and methyl ethyl ketone in short exposure. It swells in non-polar hydrocarbons—aromatic solvents, chlorinated solvents, fuels, and mineral oils—and degrades in concentrated acids and bases, which catalyze hydrolysis of the Si-O backbone. Silicone is not a universal chemical seal.
The pattern is consistent enough to state as a rule: polar media are largely safe; non-polar media are not. Silicone’s low surface energy repels polar molecules, so methanol, ethanol, isopropanol, weak acids, and mild bases leave the network intact. Non-polar molecules with small molecular size slip between the polymer chains, and aromatic compounds do it most aggressively.
Medium-by-medium, the behavior breaks down like this:
| Medium category | Examples | Silicone performance | Failure mode | Alternative elastomer |
|---|---|---|---|---|
| Water, steam | Potable water, salt water, autoclave steam | Excellent to ~150°C | None within range | — |
| Dilute acids and bases | 30% sulfuric acid, 10% sodium hydroxide | Good at room temperature | Slow surface attack at high temperature | FKM for hot service |
| Alcohols, glycols | Ethanol, isopropanol, brake fluid | Gut | Keine | — |
| Vegetable and animal oils | Food oils, fats | Gut | Keine | — |
| Ketones, esters | Acetone, MEK, ethyl acetate | Fair, short exposure only | Reversible swelling 30-80% | FKM, FFKM |
| Aromatic hydrocarbons | Benzene, toluene, xylene | Poor | Swelling 50-150%, softening | FKM, FFKM |
| Chlorinated solvents | Methylene chloride, trichloroethylene | Poor | Swelling 80-200%, dissolution | FFKM |
| Fuels | Gasoline, diesel | Poor | Swelling 20-60%, rapid softening | NBR, HNBR, FVMQ |
| Mineral and transformer oils | Lubricating oil, hydraulic fluid | Fair | Moderate swelling | NBR, HNBR |
| Concentrated acids and bases | Concentrated sulfuric acid, nitric acid, caustic | Poor | Hydrolysis, cracking, hardening | FKM, FFKM, PTFE |
This table matches the medium-compatibility breakdown published by rubber distributors such as Timco Rubber, whose material guides list dilute acids, alkalies, and oxygenated solvents as silicone-compatible and concentrated acids, aromatic hydrocarbons, and chlorinated solvents as incompatible.
The practical takeaway for a specification is that silicone covers a wide share of industrial sealing work, but the exceptions are predictable. If your medium appears in the lower half of that table, don’t test silicone harder—move to a different elastomer family.
Which chemicals actually destroy silicone?
Two mechanisms do the damage, and they look different in service.
Swelling. Non-polar solvents diffuse into the crosslinked network and push the chains apart. The part grows in volume—20% to 60% in fuels, 50% to 150% in aromatics, and 80% to 200% in chlorinated solvents depending on grade and temperature. Swelling softens the compound, drops tensile strength, and destroys the dimensional fit the seal was designed around. Even when the solvent later evaporates and the part returns closer to its original size, the recovery is incomplete, and repeated cycles accelerate the loss. A swollen silicone gasket has already failed as a gasket even if it doesn’t look damaged.
Hydrolysis. Concentrated acids and bases attack the Si-O bond directly. At moderate concentrations this shows up as progressive surface degradation over months; at high concentrations the reaction is fast enough to break the part down in a single exposure. The visible signs are cracking, hardening, and loss of flexibility—the opposite of swelling, which is worth knowing when you’re diagnosing a returned part.
A third, slower mechanism appears in high-pressure steam above about 120 °C, and it follows the hydrolysis route rather than the swelling route.
A field check takes fifteen minutes and no equipment beyond a scale. Cut a test piece, weigh it, submerge it in the actual medium at the actual service temperature for 24 hours, then dry the surface and weigh again. A thickness increase of more than about 5% signals incompatibility, and the part should move to a different material. Suppliers run the same test to ISO 1817 or ASTM D471 before quoting a compound, and the results are far more reliable than a general compatibility chart when concentration or temperature sits near a boundary.
Choosing the right silicone grade for the environment
Grade choice follows from the three boundaries already covered, but hardness gets decided last and often badly.
Hardness sets the trade-off between conformability and extrusion resistance. Soft compounds (30-50 Shore A) deform around surface imperfections and seal at low compression force, which suits irregular castings, thin-walled enclosures, and low-pressure covers. Harder compounds (60-80 Shore A) resist extrusion under pressure and hold their shape under load, which is what flanged joints and higher-pressure gasketing need. Silicone’s Shore A range runs from about 30 to 90 depending on formulation, so the choice belongs in the specification rather than the drawing notes.
Compression set matters alongside hardness. A post-cured silicone compound tested to ASTM D395 Method B at 175 °C for 22 hours typically lands in the 15-25% range, which is acceptable for static gaskets and marginal for dynamic duty. If the seal experiences repeated compression cycles, expect it to take a permanent set and plan the gland depth accordingly.
Tensile and tear strength are silicone’s weakest mechanical properties and worth stating up front. Unfilled silicone pulls at roughly 5-10 MPa with tear strength in the 10-15 kN/m band, well below a carbon-black-reinforced nitrile or EPDM compound. Fumed silica reinforcement lifts tensile to about 12-15 MPa and tear to 30-50 kN/m, but the ceiling stays lower than oil-resistant rubbers reach. This is why silicone belongs in static seals, flexible connectors, and slow-speed diaphragms, and not in reciprocating shaft seals or high-pressure hydraulic glands where abrasion and extrusion dominate.
Cure system and compliance
The cure chemistry affects chemical performance as much as the base polymer does, and it’s frequently left off the datasheet.
Peroxide-cured silicone, common in industrial grades, generally handles non-polar solvents better than platinum-cured material. Platinum-cured (addition-cure) silicone crosslinks without releasing by-products, which makes it the standard route for food and medical parts, but the trade-off is that platinum systems are also more susceptible to inhibition and to attack in certain aggressive media. If your application involves both solvent contact and a cleanliness requirement, that conflict needs resolving before tooling.
Compliance requirements follow the end use. Platinum-cured silicone meets FDA 21 CFR 177.2600 for repeated food contact, and USP Class VI covers short-term implant and medical device applications alongside ISO 10993-5 and -10 for cytotoxicity and sensitization. Both routes normally require a documented post-cure—typically four hours at 200°C—to drive off residual volatiles and oligomers, and a peroxide-cured compound can only meet the same extractable limits after the same post-cure. If the datasheet doesn’t state the cure system, ask before qualifying the compound for food-plant or pharmaceutical service.
Getting the specification into the RFQ
A rubber material callout under ASTM D2000 encodes the base polymer, heat-resistance class, and a set of physical requirements in one line, which removes most of the ambiguity from a quotation. Silicone sits under type FC, FE, or GE in that system, and quoting the full line callout rather than “food-grade silicone” prevents suppliers from substituting a compound that meets the label but not the performance requirement.
The point where buyers get surprised is that a “food-grade” label without an FDA 21 CFR 177.2600 reference isn’t a verified food grade, and a “medical-grade” label without USP Class VI documentation is a marketing claim rather than a qualification. Shore A readings taken on an under-cured plaque can also be off by 3-5 points, so asking for a press-cured datasheet and a seven-day cured test slab at 23°C and 50% relative humidity gives you numbers you can actually compare.
Seal formats: strip, tape, ring, and gasket
The same compound behaves differently depending on what shape it’s formed into, mostly because the failure modes differ by geometry.
| Format | Typical installation | Common applications | Design note |
|---|---|---|---|
| Silikondichtungsstreifen | Extruded profile pressed into a channel or groove | Door and window seals, enclosure gasketing, oven doors | Profile geometry controls sealing force more than hardness does. |
| Silikon-Dichtungsband | Self-adhesive backing applied to a flat face | Panel seams, quick repairs, low-pressure covers | Adhesive bond, not the silicone, is usually the first failure point. |
| Silikon-Dichtungsring | Circular cross-section seated in a gland | Static face seals, potable water fittings, cap seals | Requires defined gland depth; check compression set |
| Silikondichtung | Die-cut or molded sheet, often flanged | Food and pharmaceutical equipment, sanitary flanges, heat exchangers | Specify thickness tolerance and cure system; post-cure drives extractables. |
Extruded strip suits long runs and irregular outlines where a molded part would need expensive tooling. Tape works well when the joint face is flat and the pressure is low, but it inherits the adhesive’s temperature limit, which is usually below the silicone’s. Rings concentrate sealing force on a small contact area, which is efficient but unforgiving of gland tolerance. Gaskets cover larger areas and carry flanged joints, and for sanitary service the cure system and post-cure condition matter as much as the compound itself.
For buyers sourcing custom profiles rather than standard stock, engaging a Hersteller von maßgefertigten Silikondichtungen early shortens the loop between the drawing and a workable compound, since tooling, hardness, and the cure system interact and are cheaper to settle together than in sequence.
When silicone is the wrong choice
Silicone is the right answer for a wide band of sealing work, and it’s the wrong answer in five recognizable situations:
- Fuel or aromatic solvent contact. Gasoline and diesel swell silicone 20-60%; toluene and xylene push it to 50-150%. Move to nitrile or HNBR for petroleum media, or fluorosilicone where the temperature is also high.
- Concentrated acids or bases. Hydrolysis breaks the backbone. FKM, FFKM, and PTFE are the practical routes.
- Continuous high-pressure steam above roughly 120°C at 1.7 bar. EPDM handles steam better and costs less.
- Gas-tight or vacuum service. Silicone’s permeability to gases runs an order of magnitude or more above butyl rubber, so vacuum seals and gas-barrier applications rarely use it.
- Dynamic seals under abrasion or high pressure. Low tear strength and extrusion resistance rule silicone out of reciprocating shaft seals and hydraulic gland packings. A custom silicone rubber O-ring for sealing is a sound and economical choice for round-section static duty, as long as the environment stays within silicone’s acceptable limits.
If your application sits in one of those five categories, the sensible move is to send the medium, its concentration, the service temperature, and the exposure duration to a supplier and ask for a compound recommendation backed by test data. Where the environment does stay inside silicone’s window, a custom silicone rubber O-ring for sealing remains a sound and economical choice for round-section static duty. Chemical compatibility at a boundary condition is a testing question, and a compatibility chart only narrows the field.
Häufig gestellte Fragen
Does silicone degrade in sunlight or outdoor exposure?
No. Silicone resists UV, ozone, and weathering essentially without additives, and outdoor service life is measured in decades rather than years in most construction and electrical uses. Color compounds can fade over time, which is a cosmetic change rather than a functional one, and doesn’t affect sealing force or elasticity.
Does a higher Shore A hardness make a silicone seal more chemically resistant?
No. Hardness and chemical resistance are independent properties. A 70 Shore A silicone gasket swells in toluene exactly as a 40 Shore. A gasket does; the harder compound simply resists extrusion better while it’s swelling. Match hardness to the mechanical load and choose a different elastomer family when the medium itself is the problem.
How long does a silicone seal last?
In static service inside its temperature and chemical window, service life commonly runs 15-20 years, and storage life on unopened stock is quoted around 20 years by compounders. Actual life shortens predictably with temperature—roughly halving with each additional 10-15°C above the continuous rating—and shortens sharply once chemical swelling or hydrolysis begins.
